Pyon's Diary

成る可くJIS X 0213:2004對應MSフォント(5.0)、IPAフォント(003.02)で御覽下さい

2007-06-17 舊平成拾玖年皐月参日 (日・晴) [長年日記]

(No.11) HDS721680PLA380 (Deskstart 7K160, Hitachi)を取附けた。

外附USBのHDDでは初期化は出來たがファイルの作成が出來無かつたので、結局S-ATAのHDDを買つて來た。

買つて來たのは、有樂町のビックカメラで一番安かつた日立の

HDS721680PLA380 (Deskstart 7K160)

と云ふ奴。

取附ける。

取敢へず取附けて起動。起動メッセージを眺めた限り認識してゐる樣子。

Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Hitachi   Model: HDS721680PLA380   Rev: P21O
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0

初期化する。

其れでは開發環境を作成してみようと云ふ事でKUROBOX/PRO 製品仕樣書の拾貳頁5.3.2. 初期化 SWに買いて在る通り初期化スイッチ*1を五秒程押して見た。

dmesgの出力は以下の通り。

md: Autodetecting RAI: sda1
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1

何かあつと云ふ間にをはつた。本當に搭載されてゐるかを確認する。

# mount
/dev/root on / type jffs2 (rw,noatime)
proc on /proc type proc (rw,nodiratime)
sysfs on /sys type sysfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
/dev/mtd3 on /mnt/mtd type jffs2 (rw,noatime)
/dev/sda1 on /mnt/disk1 type xfs (rw)

正常に搭載されてゐる樣に見える。

ファイルを作成する。

以前、外附HDD (USB)を取附けた時はファイルの作成が出來無かつたので今度はどうか試して見た。

# cd /mnt/disk1/
# ls -a
.   ..
# touch a
# ls -a
.   ..  a

今度はファイルの作成が出來た。vimで編輯して保存も可能。

外附HDD (USB)が駄目だつた原因は何だつたのだろう。USBのドライバが惡かつたのだろうか。

開發環境を構築した。

何とか使へさうなのでKUROBOX/PRO 製品仕樣書の廿玖頁Appendix B: 開發環境の構築方法を見乍ら開發環境の構築を行つた。

開發環境が入つたhddrootfs.tar.gzを持つて行く爲に外附HDD (USB)を經由して持つて行く事にした。KURO-BOX/PROに外附HDD (USB)を繋ぐと矢張り認識はした。

usb 1-1: new high speed USB device using ehci_platform and address2
usb 1-1: config 1 descriptor has 1 excess byte, ignoring
scsi2 : SCSI emulation for USB Mass Storage devices
  Vendor: FUJITSU   Model: MHT2020AT         Rev: 0811
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdb: 39070080 512-byte hdwr sectors (20004 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 39070080 512-byte hdwr sectors (20004 MB)
sdb: assuming drive cache: write through
 sdb: sdb1
Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0,  type 0

搭載も出來た。

# mount -t ext3 /dev/sdb1 /mnt/usbdisk1
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
# mount
/dev/root on / type jffs2 (rw,noatime)
proc on /proc type proc (rw,nodiratime)
sysfs on /sys type sysfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
/dev/mtd3 on /mnt/mtd type jffs2 (rw,noatime)
/dev/sda1 on /mnt/disk1 type xfs (rw)
/dev/sdb1 on /mnt/usbdisk1 type ext3 (rw)

hddrootfs.tar.gzを内臟HDDに複寫した。

# cp /mnt/usbdisk1/hddrootfs.tar.gz /mnt/disk1/
# ls -l /mnt/usbdisk1/hddrootfs.tar.gz /mnt/disk1/hddrootfs.tar.gz
-rw-r--r--    1 root     root     67260248 Jun 17 19:39 /mnt/disk1/hddrootfs.tar.gz
-rw-r--r--    1 root     root     67260248 Jun 17 19:33 /mnt/usbdisk1/hddrootfs.tar.gz

どきゞゝし乍らファイルを解凍・展開した。

# tar zxvf hddrootfs.tar.gz -C /mnt/disk1
./bin
./bin/bash
./bin/bash2
(中略)
./var/lock/subsys
./var/proftpd
./var/www

今度は上手く云つた模樣。外附USBで駄目なのは何だつたのかと惱む。

開發環境を試す。

開發環境にchrootしてHello World!をコンパイルしてみた。

# chroot /mnt/disk1


BusyBox v1.1.1 (2006.11.29-02:37+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# cd
# vi test.c
# gcc -o test.exe test.c
# ./test.exe
Hello World!

C言語の書き方を忘れてゐて少し焦つた。もう五年以上書いてゐ無い。

其れは其れとしてファイルの編輯、コンパイルが漸く出來た。こんな事なら最初から内臟HDDを買つて來るのだつた。

| Permalink

*1 本體背面に在る紅い釦。筆先で押す。

(No.12) HDD起動環境にした。

2007-11-03 [注意] 此處の手順を始める前に初期化スクリプトの修正を行ふ事。然うしないとファイルシステムの作成に失敗したり、スワップ領域が作成され無かつたり、色々呪はれる事に成る。

毎度chrootにするのも面倒臭いのでKUROBOX/PRO 製品仕樣書の參拾壹頁Appendix B: 開發環境の構築方法に随つてHDDブート環境にして見た。

必要なファイルを/mnt/mtdに複寫した。

附屬CD-ROMのdevelopment_kitの中に在る以下のファイルをKURO-BOX/PROの/mnt/mtdに複寫した。

ChangeMeDevHDD -- HDDパーティションを開發用にする爲の意思表示ファイル。
ChangeMyUbootEnv -- u-boot の環境變數を書換へる爲の意思表示ファイル。
hddrootfs.tar.gz -- 開發環境用ファイル群。
uImage.buffalo -- カーネル。

複寫後取敢へず確認した。當たり前だが山下さんの所と同じ。

# ls -la /mnt/mtd
drwxrwxrwx    3 root     root            0 Jun 17 21:01 .
drwxr-xr-x   10 root     root            0 Jun 17 18:30 ..
-r-xr-xr-x    1 root     root            0 Jun 17 20:59 ChangeMeDevHDD
-r-xr-xr-x    1 root     root            0 Jun 17 20:59 ChangeMyUbootEnv
-rw-r--r--    1 root     root     67260248 Jun 17 21:01 hddrootfs.tar.gz
-r-xr-xr-x    1 root     root      1736436 Jun 17 21:01 uImage.buffalo

内臟HDDからパーティションを削除した。

其れから内臟HDDからパーティションを削除した。

# fdisk /dev/sda

The number of cylinders for this disk is set to 10011.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)

Command (m for help): p

Disk /dev/sda: 82.3 GB, 82348277760 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot    Start       End    Blocks   Id  System
/dev/sda1               1       10011    80413326   83  Linux

Command (m for help): d
Selected partition 1

Command (m for help): p

Disk /dev/sda: 82.3 GB, 82348277760 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot    Start       End    Blocks   Id  System

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda:
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda:
Syncing disks.

此だけやつて一旦落としてから再度起動した。

初期化スイッチを五秒押した。

立ち上がつた所で初期化スイッチを五秒押した。コンソールに色々状況が出力されてINFO燈(橙色)が點滅し出した。

SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4

此處で餘りにも長い時間(壹時間程)待たされたのでpsを見ると/dev/sda2のフォーマットをずつとしてゐた。何か變だと思ひ一旦 shutdown して再起動、其れから内臟HDDのパーティションを全て消してもう一度再起動した。

其れから再度初期化スイッチを五秒押ししてみたが矢張り駄目。

一個上手く行つても次が駄目に成るなあ。玄人志向は向いてゐ無いのかなあ。

自分でフォーマットした。

仕方が無いので何度が再起動して初期化スイッチを押しても/dev/sda2のフォーマットで止まつて了ふので、/dev/sda1をEXT3で/dev/sda2をXFSでフォーマットして再度初期化スイッチを押してみた。(何故か/dev/sda4はXFSでフォーマットされてゐた。)

でも

disk is already formatted!

と出て駄目だつた。

DiskDelete.sh

以下は推測の話だが、内臟HDDがパーティションを切つてゐ無い状態で初期化スイッチを五秒押しすると、パーティション作成後各パーティションのフォーマットで何かゞ變に成り、其之後は處理が進ま無く成つて了ふ模樣。

其處で進ま無く成つた時點で一旦再起動し、今度はパーティションは消さずにDiskDelete.sh *1を使つてフォーマット情報を一旦削除した上で亦再起動をし、其處で初期化スイッチを五秒押した。

DiskDelete.shの事は以下の頁で知つた。

KURO-BOX/PROのBBS -- 工場出荷時に戻すには。

中を覗いて見ると、sda1, sda2, sda3, sda4 の先頭に0を埋めてゐるだけだつた。兎に角實行した。

# /usr/local/bin/DiskDelete.sh
umount: forced umount of /mnt/disk1 failed!
512+0 records in
512+0 records out
512+0 records in
512+0 records out
512+0 records in
512+0 records out
512+0 records in
512+0 records out
512+0 records in
512+0 records out

其れから祈る樣な氣持で初期化スイッチを五秒押しするとコンソールに期待してゐた出力された。

SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
XFS mounting filesystem sda2

再度山下さんの處を元に比較して見た。

# mount
/dev/root on / type jffs2 (rw,noatime)
proc on /proc type proc (rw,nodiratime)
sysfs on /sys type sysfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
devpts on /dev/pts type devpts (rw)
/dev/ram1 on /mnt/ram type tmpfs (rw)
/dev/mtd3 on /mnt/mtd type jffs2 (rw,noatime)
/dev/sda1 on /mnt/boot type ext3 (rw)
/dev/sda2 on /mnt/rootfs type xfs (rw)
# df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/mtd2                64.0M     15.6M     48.4M  24% /
/dev/ram1                 8.0M    144.0k      7.9M   2% /mnt/ram
/dev/mtd3               188.0M     70.8M    117.2M  38% /mnt/mtd
/dev/sda1                53.1M      5.7M     44.7M  11% /mnt/boot
/dev/sda2                 2.8G    213.7M      2.6G   7% /mnt/rootfs
# ls -la /mnt/boot
drwxr-xr-x    3 root     root         1024 Jun 17 23:54 .
drwxr-xr-x   12 root     root            0 Jun 17 23:54 ..
drwx------    2 root     root        12288 Jun 17 23:53 lost+found
-r-xr-xr-x    1 root     root      1736436 Jun 17 21:01 uImage.buffalo
# ls -l /mnt/rootfs
drwxr-xr-x    2 root     root         4096 Jun 17 23:54 bin
drwxr-xr-x    2 root     root            6 Feb  7 15:11 boot
drwxr-xr-x    6 root     root         4096 Jun 17 23:54 dev
drwxr-xr-x   12 root     root         4096 Jun 17 23:54 etc
drwxr-xr-x    2 root     root            6 Feb  7 15:11 home
drwxr-xr-x    4 root     root         4096 Jun 17 23:54 lib
drwxr-xr-x    2 root     root            6 May 16  2006 mnt
drwxr-xr-x    2 root     root            6 Jan 31  2006 proc
drwx------    2 root     root            6 Jan 31  2006 root
drwxr-xr-x    2 root     root         4096 Jun 17 23:54 sbin
drwxr-xr-x    2 root     root           20 Jun 17 23:54 share
drwxr-xr-x    2 root     root            6 Feb  7 15:11 sys
drwxr-xr-x    2 root     root            6 Jan 31  2006 tmp
drwxr-xr-x   10 root     root           99 Jun 17 23:56 usr
drwxr-xr-x   10 root     root           93 Jun 17 23:56 var

大丈夫みたいなので再起動した。

Orion1   CPU =  Low

=== KURO U-Boot. ===
 ** LOADER **
 ** KUROBOX BOARD: KURO_BOX  LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz


USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
<<system_bootend>>
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: Hitachi HDS721680PLA380                  Firm: P21OAB3A Ser#:       PVC1J
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 78533.4 MB = 76.6 GB (160836480 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1736436 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2007-02-08   6:00:09 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1736372 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_KUROBOX ---
Uncompressing Linux.............................................................
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeS7
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 425K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
 config_device_cs Error : Unknown board

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size   1MB
INTER_REGS ....base f1000000, size   1MB
DEVICE_CS0 ....base fa000000, size   2MB
DEVICE_CS1 ....base f4000000, size  32MB
DEVICE_CS2 ....base fa800000, size   1MB
DEV_BOOCS ....base ff800000, size   8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
BUFFALO KUROBOX FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- BUFFALO_BOARD_2

 Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e0)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (10)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Hitachi   Model: HDS721680PLA380   Rev: P21O
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec4
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 De4
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   arm4regs  :   304.000 MB/sec
   8regs     :   215.200 MB/sec
   32regs    :   249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
XFS mounting filesystem sda2
Starting XFS recovery on filesystem: sda2 (dev: sda2)
Ending XFS recovery on filesystem: sda2 (dev: sda2)
VFS: Mounted root (xfs filesystem).
Freeing init memory: 112K
init started:  BusyBox v1.1.1 (2006.11.29-02:37+0000) multi-call binary
Starting pid 223, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (hddroot) ---
===== Starting checkroot.sh =====
grep: /proc/mtd: No such file or directory
grep: /proc/mtd: No such file or directory
grep: /proc/mtd: No such file or directory
chown: unknown group name: rpcuser
grep: /proc/buffalo/firmware: No such file or directory
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]

===== Starting MountSystemFolders =====
[Success]

Setting up swapspace version 1, size = 139825152 bytes
Adding 136544k swap on /dev/sda3.  Priority:-1 extents:1
===== Starting Kevent.sh =====
[Success]

===== Starting mount_share.sh =====
Mounting /dev/sda4 on /home as a xfs file system.
XFS mounting filesystem sda4
Success.

Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
mount: mount point /mnt/mtd does not exist
Failed.
[Failed ]

===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]

===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP  tout=30[s]
** dhcp fail
** setting default ip
route: SIOC[ADD|DEL]RT: No such process
add default if
hostname is setted to KUROBOX-PRO
[Success]

===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]

===== Starting FanController.sh =====
[Success]

===== Starting bootcomplete.sh =====
[Success]

Starting pid 582, console /dev/ttyS0: '/sbin/getty'

KUROUTOSHIKOU KUROBOX Series
KUROBOX-PRO login:

起動した。結局何で只初期化スイッチを押しただけでは駄目だつたのか判ら無い。